
Features of wire rope electric hoists
Application in productive heavy industries
With the ability to install a winch (hoist) towing wire
Loading capacity from 2.3 tons to 100 tons
Span from 6 meters to 32 meters
Different structural working groups: A3 to A8
Rise (def):
A3 to A5 : def (1/600 ~ 1/800) & A6 to A8 : def (1/1000 ~ 1/1200)
Different movement speeds - has six electric movements
Has longitudinal and transverse movement microswitches
Optional
Bus bar and bus power supply system for longitudinal movements
Alkyd paint coating, epoxy polyamine, epoxy polyamide, polyurethane
Loading capacity 120 tons to 320 tons
Span from 32 meters to 50 meters
Equipped with Load Limited

Electrical Wire Rope Hoist Specifications
Overhead lifting devices have different types and shapes and functional mechanisms, but almost all of them have a very important functional member and part in common. The lift section is present in all cranes. Industrial elevators are produced and supplied in two types, the chain group and the wire rope group, their actuators are manual or electric and sometimes hydraulic, each of which has its own characteristics and uses, which are related to wire rope elevators and their use in this section. let's pay
Towing rope hoists have many varieties, each of which has a specific use, electric towing hoists are divided into two types, single-speed and two-speed, and they work with three-phase or single-phase electricity and have There are also different movement speeds, in general, the towing lifts are four-way or double-way, which means that lifts with only hook movement up and down are called double-way.
And in the case where up and down movement and lateral movement are needed on both sides, four-way or four-way elevators should be used, these types of elevators can be used in different industries, and these types of elevators are used for All kinds of industrial cranes are used.
In these lifts, steel ropes called tow wire are wrapped around a metal cylinder that must be machined exactly according to the diameter of the tow wire and have grooves, and that metal cylinder (known as wire guide), wire They guide the towing and finally lift the load with a hook that actually consists of a pulley and a hook at the end.
The law of compound pulleys allows the lifting spectrum to move even very heavy loads, although according to the same law of compound pulleys, it should be noted that with the addition of pulleys, the lifting speed decreases and increases in proportion to the capacity. This work (knowing the mechanism of pulleys and increasing and decreasing capacity and speed) is very specialized, and before implementation, you must pay attention to the cable hoist catalog and observe the technical points and standard requirements.

Use of electric industrial wire rope hoists
Cranes and electric industrial wire rope hoists are classified according to different standards for different uses in light and heavy industries
- Permanent working time 5M
- Very productive 4M
- Prolific 3M
- Average work 2M
- Low work 1AM
- Rarely work 1BM
The work group should be selected correctly and accurately according to the type of work to ensure the use of the lift in the desired direction. Therefore, for a safe and affordable selection, the consultants of the sales unit are ready to answer.

Features of wire rope hoists
- Steering wheel switch with 24V power
- Two variable speeds using inuter
- single speed and double speed of all movements
- Selection of loading capacity from 1 ton to 60 tons
- limit switches (up/down)
- Number of switches 180 to 420 times per hour
- Long life of gearboxes due to proper design
- suitable for use in light industries with height restrictions
- Steering wheel control by cable or remote control
- Working groups and height required by the number of different strands of towing wire
- Standard Requirements for Functional Safety
- Selection of loading capacity from 1 ton to 60 tons
- Fast movement thanks to the high speed of the crane
- Long life of gearboxes due to proper design
- Long life of the electric motor and brake by using the inverter
- Using the best raw materials in construction
- Using the best European standard parts such as: towing wire, hook, electric motor and other parts

Components of electric tow wire hoist
Tow wire hoists consist of the following main parts:
1- Electromotor
2- Magnetic brake or brake with cone mechanism
3-Gearbox with reducing steel gear
4-Towing wire
5-Reel and hook
6- Electric panel
